| General specifications |
|---|
| Sensing range | 60 … 2000 mm |
| Adjustment range | 80 … 2000 mm |
| Dead band | 0 … 60 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 175 kHz |
| Nominal ratings |
|---|
| Response delay | minimum: 60 ms
factory setting: 330 ms |
| Time delay before availability | ≤ 1600 ms |
| Indicators/operating means |
|---|
| LED green | Operating display |
| LED yellow | object in evaluation range |
| LED red | error |
| Electrical specifications |
|---|
| Operating voltage | 12 … 30 V DC , ripple 10 %SS |
| No-load supply current | ≤ 50 mA |
| Interface |
|---|
| Interface type | Serial interface (programming adapter required)
9600 BPS, no parity, 8 data bits, 1 stop bit |
| Input/Output |
|---|
| Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 … 1 V |
| 1 Level | 4 V … UB |
| Input impedance | > 12 kΩ |
| Output rated operating current | < 12 mA |
| Pulse length | 0.5 … 300 ms (level 1) |
| Pulse interval | ≥ 33 ms (level 0) |
| Synchronization frequency | |
| Common mode operation | ≤ 30 Hz |
| Multiplex operation | ≤ 33 Hz / n , n = number of sensors , n ≤ 10
(factory setting: n = 5 ) |
| Input |
|---|
| Input type | 1 program input |
| Level (evaluation limit 1) | 0 … 1 V |
| Level (evaluation limit 2) | 4 V … UB |
| Input impedance | > 12 kΩ |
| Pulse length | 2 … 10 s |
| Output |
|---|
| Output type | 1 analog output 0 … 10 V |
| Resolution | evaluation range [mm]/4000, but ≥ 0.4 mm |
| Deviation of the characteristic curve | ≤ 0.2 % of full-scale value |
| Repeat accuracy | ≤ 0.1 % of full-scale value |
| Load impedance | ≥ 500 Ohm |
| Temperature influence | ≤ 1.5 % of full-scale value |
Compliance with standards and directives |
|---|
| Standard conformity | |
| Standards | EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
EN 60947-5-7:2003
IEC 60947-5-7:2003 |
| Approvals and certificates UC2000-L2-U-V15 |
|---|
| UL approval | cULus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) |
| Mechanical specifications |
|---|
| Connection type | Connector plug M12 x 1 , 5-pin |
| Degree of protection | IP67 |
| Material | |
| Housing | PA-GF35 |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Mass | 115 g |
| Factory settings |
|---|
| Output | evaluation limit A1: 80 mm
evaluation limit A2: 2000 mm
output function: rising ramp |
| Beam width | wide |
| Evaluation procedure | low-pass behavior |
| General information |
|---|
| Supplementary information | Switch settings of the external programming adapter:
“output load”: pull-down
“output logic”: noninv |
