| General specifications |
|---|
| Signal type | Analog input |
| Supply |
|---|
| Connection | SL1: 1a, 1b(-); 2a, 2b(+) |
| Rated voltage | 20 … 30 V DC bus powered via Termination Board |
| Ripple | within the supply tolerance |
| Rated current | ≤ 22 mA |
| Power dissipation/power consumption | 0.7 W max. |
| Lockout voltage | > 11 V DC |
| Input |
|---|
| Connection side | field side |
| Connection | SL2: 5a(+), 5b(-) |
| Input resistance | ≥ 16 MΩ |
| Transmission range | 0 … ± 50 mV |
| Offset voltage/current | ≤ 5 µV / ≤ 5 nA |
| Output |
|---|
| Connection side | control side |
| Connection | SL1: 8a(+), 7a(-) |
| Voltage | 0 … ± 50 mV |
| Load | Accuracy figures for infinite load impedance. Additional 0.03 % of span for a load resistance of 10 kΩ |
| Output resistance | max. 3 Ω |
| Line fault detection | input: ± 100 mV
output: +200 mV, -115 mV |
| Fault indication output |
|---|
| Connection | SL1: 6b |
| Output type | open collector transistor (internal fault bus) |
| Fault voltage | < Vcc/2 (when connected to Vcc via 10 kΩ pull up resistor) |
| Transfer characteristics |
|---|
| Deviation | |
| After calibration | at 20 °C (68 °F):
± 3 µV up to ± 10mV/± 0.05 % of the span up to +50 mV/± 0.05 % of the span up to -50 mV |
| Influence of ambient temperature | ± 1 µV/K (typical ± 0.25 µV/K) |
| Absolute | < 0.25 K at 30 V voltage supply |
| Bandwidth | DC to > 350 Hz (-3 dB) |
| Settling time | < 2 ms |
| Rise time/fall time | ≤ 1 ms |
| Galvanic isolation |
|---|
| Output/power supply | functional insulation, rated insulation voltage 50 V AC |
| Indicators/settings |
|---|
| Display elements | LEDs |
| Control elements | DIP-switch |
| Configuration | via DIP switches |
| Labeling | space for labeling at the front |
| Directive conformity |
|---|
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Conformity |
|---|
| Electromagnetic compatibility | NE 21:2006
For further information see system description. |
| Degree of protection | IEC 60529:2001 |
| Protection against electrical shock | UL 61010-1 |
| Ambient conditions |
|---|
| Ambient temperature | -20 … 60 °C (-4 … 140 °F) |
Mechanical specifications |
|---|
| Degree of protection | IP20 |
| Mass | approx. 100 g |
| Dimensions | 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 inch) |
| Mounting | on Termination Board |
| Coding | pin 2, 3 and 4 trimmed
For further information see system description. |
| Data for application in connection with hazardous areas |
|---|
| EU-type examination certificate | BASEEFA 10 ATEX 0031X |
| Marking |   II (1)GD, I (M1), [Ex ia] IIC, [Ex iaD], [Ex ia] I (-20 °C ≤ Tamb ≤ 60 °C) [circuit(s) in zone 0/1/2] |
| Voltage | 5.5 V DC |
| Current | 2.4 mA |
| Power | 3.3 mW |
| Supply | |
| Maximum safe voltage | 253 V (Attention! The rated voltage can be lower.) |
| Certificate | BASEEFA 10 ATEX 0032X |
| Marking | II 3G Ex nA II T4 |
| Galvanic isolation | |
| Input/Output | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Input/power supply | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| International approvals |
|---|
| UL approval | |
| Control drawing | 116-0317 (cULus) |
| IECEx approval | IECEx BAS 10.0012X
IECEx BAS 10.0013X |
| Approved for | [Zone 0] [Ex ia] IIC, [Ex iaD], [Ex ia] I
Ex nA II T4 |
| General information |
|---|
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
