| General specifications |
|---|
| Sensing range | 200 … 4000 mm |
| Adjustment range | 240 … 4000 mm |
| Dead band | 0 … 200 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 85 kHz |
| Response delay | minimum : 115 ms
factory setting: 225 ms |
| Memory |
|---|
| Non-volatile memory | EEPROM |
| Write cycles | 100000 |
| Indicators/operating means |
|---|
| LED green | solid: Power on
flashing: Standby mode or IO link communication |
| LED yellow 1 | solid: Object in evaluation range
flashing: Learning function, object detected |
| LED yellow 2 | solid: Object in evaluation range
flashing: Learning function, object detected |
| LED red | solid red: Error
red, flashing: program function, object not detected |
| Electrical specifications |
|---|
| Operating voltage | 10 … 30 V DC , ripple 10 %SS
15 … 30 V voltage output |
| No-load supply current | ≤ 60 mA |
| Power consumption | ≤ 1 W |
| Time delay before availability | ≤ 150 ms |
| Interface |
|---|
| Interface type | IO-Link |
| Protocol | IO-Link V1.0 |
| Transfer rate | Acyclical: typical 54 Bit/s |
| Cycle time | min. 59.2 ms |
| Mode | COM 2 (38.4 kBaud) |
| Process data width | 16 bit |
| SIO mode support | yes |
| Input/Output |
|---|
| Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 … 1 V |
| 1 Level | 4 V … UB |
| Input impedance | > 12 kΩ |
| Output rated operating current | < 12 mA |
| Pulse length | 0.5 … 300 ms (level 1) |
| Pulse interval | ≥ 62 ms (level 0) |
| Synchronization frequency | |
| Common mode operation | ≤ 16 Hz |
| Multiplex operation | ≤ 17 Hz / n , n = number of sensors , n ≤ 10
(factory setting: n = 5 ) |
| Output |
|---|
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected
Current output 4 mA … 20 mA or
voltage output 0 V … 10 V configurable |
| Rated operating current | 200 mA , short-circuit/overload protected |
| Voltage drop | ≤ 2.5 V |
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm
voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
| Deviation of the characteristic curve | ≤ 0.2 % of full-scale value |
| Repeat accuracy | ≤ 0.1 % of full-scale value |
| Switching frequency | ≤ 2 Hz |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable |
| Load impedance | current output: ≤ 300 Ohm
voltage output: ≥ 1000 Ohm |
| Temperature influence | ≤ 1.5 % from full-scale value (with temperature compensation)
≤ 0.2 %/K (without temperature compensation) |
| Compliance with standards and directives |
|---|
| Standard conformity | |
| Standards | EN 60947-5-2:2007+A1:2012
IEC 60947-5-2:2007 + A1:2012
EN 60947-5-7:2003
IEC 60947-5-7:2003 |
| Approvals and certificates |
|---|
| UL approval | cULus Listed, General Purpose |
| CSA approval | cCSAus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) |
| Mechanical specifications |
|---|
| Connection type | Connector plug M12 x 1 , 5-pin |
| Degree of protection | IP67 |
| Material | |
| Housing | Stainless steel 1.4305 / AISI 303
TPU
Polyamides |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Mass | 95 g |
| Factory settings |
|---|
| Output 1 | near switch point: 240 mm
far switch point: 4000 mm
Output mode: Window mode
output behavior: NO contact |
| Output 2 | near limit: 500 mm
far limit: 2000 mm
Output mode: rising ramp
output behavior: Current output 4 mA … 20 mA |
| Beam width | wide |
