| General specifications |
|---|
| Sensing range | 20 … 250 mm |
| Adjustment range | 25 … 250 mm |
| Dead band | 0 … 20 mm |
| Standard target plate | 10 mm x 10 mm |
| Transducer frequency | approx. 400 kHz |
| Response delay | minimum : 8 ms
factory setting: 29 ms |
| Sensor cycle time | ≥ 8 ms (factory setting) ;
programmable to 60 s |
| Memory |
|---|
| Non-volatile memory | EEPROM |
| Write cycles | 300000 |
| Indicators/operating means |
|---|
| LED green | solid: Power on
flashing: Standby mode or IO-Link communication |
| LED yellow | solid: object in evaluation range
flashing: switch point programming, object detected |
| LED red | solid: error
flashing: switch point programming, object not detected |
| Electrical specifications |
|---|
| Operating voltage | 10 … 30 V DC , ripple 10 %SS |
| No-load supply current | ≤ 40 mA |
| Power consumption | ≤ 400 mW |
| Time delay before availability | ≤ 300 ms |
| Interface |
|---|
| Interface type | IO-Link (via C/Q = Pin 4) |
| Device profile | Smart Sensor |
| Transfer rate | COM 2 (38.4 kBaud) |
| IO-Link Revision | 1.1 |
| Min. cycle time | 2.3 ms |
| Process data width | 16 bit |
| SIO mode support | yes |
| Device ID | 0x300300 (3146496) |
| Compatible master port type | A |
| Input/Output |
|---|
| Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 … 1 V |
| 1 Level | 2.5 V … UB |
| Input impedance | > 22 kΩ |
| Output rated operating current | current source < 2.5 mA |
| Pulse length | ≥ 1 ms with external control, low active |
| Synchronization frequency | |
| Common mode operation | ≤ 141 Hz |
| Multiplex operation | ≤ 141 Hz / n , n = number of sensors , n ≤ 10 |
| Output |
|---|
| Output type | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected |
| Rated operating current | 100 mA , short-circuit/overload protected |
| Voltage drop | ≤ 2.5 V |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value |
| Switching frequency | factory setting: 20 Hz programmable max. 45 Hz |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm |
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0,17 %/K (without temperature compensation) |
| Compliance with standards and directives |
|---|
| Standard conformity | |
| Standards | EN 60947-5-2:2007+A1:2012
IEC 60947-5-2:2007 + A1:2012
IEC 61131-9:2013 |
| Approvals and certificates |
|---|
| UL approval | cULus Listed, Class 2 Power Source |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) |
| Mechanical specifications |
|---|
| Connection type | Connector plug M8 x 1 , 4-pin |
| Degree of protection | IP67 |
| Material | |
| Housing | Polycarbonate |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Installation position | any position |
| Mass | 9 g |
| Tightening torque, fastening screws | max. 0.2 Nm |
| Factory settings |
|---|
| Output | near switch point: 25 mm
far switch point: 250 mm
Output mode: Window mode
Output logic: normally open |
| Beam width | wide |
