| General specifications |
|---|
| Measurement range | 100 … 550 mm |
| Reference target | standard white, 100 mm x 100 mm |
| Light source | LED |
| Light type | modulated visible red light |
| LED risk group labelling | exempt group |
| Angle deviation | max. +/- 1.5 ° |
| Diameter of the light spot | approx. 20 mm at a distance of 550 mm |
| Angle of divergence | 2.5 ° |
| Ambient light limit | EN 60947-5-2 : 45000 Lux |
| Resolution | 0.1 mm |
| Functional safety related parameters |
|---|
| MTTFd | 520 a |
| Mission Time (TM) | 20 a |
| Diagnostic Coverage (DC) | 0 % |
| Indicators/operating means |
|---|
| Operation indicator | LED green:
constantly on – power on
flashing (4Hz) – short circuit
flashing with short break (1 Hz) – IO-Link mode |
| Function indicator | LED yellow:
constantly on – switch output active
constantly off – switch output inactive |
| Control elements | Teach-In key |
| Control elements | 5-step rotary switch for operating modes selection |
| Electrical specifications |
|---|
| Operating voltage | 18 … 30 V DC |
| Ripple | max. 10 % |
| No-load supply current | < 25 mA at 24 V supply voltage |
| Protection class | III |
| Interface |
|---|
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| Device profile | Identification and diagnosis
Smart Sensor type 0/type 3.3 |
| Transfer rate | COM 2 (38.4 kBaud) |
| IO-Link Revision | 1.1 |
| Min. cycle time | 3 ms |
| Process data width | Process data input 4 byte
Process data output 2 bits |
| SIO mode support | yes |
| Device ID | 0x111902 (1120514) |
| Compatible master port type | A |
| Output |
|---|
| Switching type | The default setting is:
C/Q – Pin4: NPN normally open, PNP normally closed, IO-Link
I—Pin2: analog output 4…20 mA |
| Signal output | 1 push-pull output , 1 analog output , short-circuit-proof, reverse polarity protection, surge-proof |
| Switching voltage | max. 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Usage category | DC-12 and DC-13 |
| Voltage drop | ≤ 1.5 V DC |
| Response time | 2 ms , see table 1 |
| Analog output |
|---|
| Output type | 1 current output: 4 … 20 mA |
| Load resistor | > 1 kΩ voltage output ; ≤ 470 Ω current output |
| Recovery time | 2 ms |
| Conformity |
|---|
| Communication interface | IEC 61131-9 |
| Product standard | EN 60947-5-2 |
| Measurement accuracy |
|---|
| Temperature drift | 0.05 %/K |
| Warm up time | 5 min |
| Repeat accuracy | ≤ 1 % , see table 1 |
| Linearity error | 0.75 % |
| Approvals and certificates |
|---|
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature | 10 … 50 °C (50 … 122 °F) |
| Storage temperature | -40 … 70 °C (-40 … 158 °F) |
| Mechanical specifications |
|---|
| Housing width | 15 mm |
| Housing height | 50.6 mm |
| Housing depth | 41.7 mm |
| Degree of protection | IP67 / IP69 / IP69K |
| Connection | 4-pin, M12 x 1 connector, 90° rotatable |
| Material | |
| Housing | PC (Polycarbonate) |
| Optical face | PMMA |
| Mass | approx. 37 g |
