| General specifications |
|---|
| Sensing range | 60 … 800 mm |
| Adjustment range | 70 … 800 mm |
| Dead band | 0 … 60 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 255 kHz |
| Response delay | minimum : 13 ms
factory setting: 49 ms |
| Sensor cycle time | ≥ 13 ms (factory setting) ;
programmable to 60 s |
| Memory |
|---|
| Non-volatile memory | EEPROM |
| Write cycles | 300000 |
| Indicators/operating means |
|---|
| LED green | solid: power on
flashing: standby mode or IO-Link communication |
| LED yellow | solid: object in evaluation range
flashing: programming of the limits, object detected |
| LED red | solid: fault
flashing: programming limits, object not detected |
| Electrical specifications |
|---|
| Operating voltage | 18 … 30 V DC , ripple 10 %SS |
| No-load supply current | ≤ 50 mA |
| Power consumption | ≤ 500 mW |
| Time delay before availability | ≤ 300 ms |
| Interface |
|---|
| Interface type | IO-Link (available after activation via programming button until next reset) |
| Input/Output |
|---|
| Input/output type | 1 synchronization connection, bidirectional |
| 0 Level | 0 … 1 V |
| 1 Level | 2.5 V … UB |
| Input impedance | > 22 kΩ |
| Output rated operating current | current source < 2.5 mA |
| Pulse length | ≥ 1 ms with external control, low active |
| Synchronization frequency | |
| Common mode operation | ≤ 82 Hz |
| Multiplex operation | ≤ 82 Hz / n , n = number of sensors , n ≤ 10 |
| Output |
|---|
| Output type | 1 analog output 0 (4) … 20 mA or
1 analog output 0 … 10 V |
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm
voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value |
| Load impedance | current output: ≤ 500 Ohm
voltage output: ≥ 1000 Ohm |
| Temperature influence | ≤ ± 0.75 % of the end value (with temperature compensation) from 10 minutes after switching on the sensor ; 0.17 %/K (without temperature compensation) |
| Compliance with standards and directives |
|---|
| Standard conformity | |
| Standards | EN 60947-5-2:2007+A1:2012
IEC 60947-5-2:2007 + A1:2012
EN 60947-5-7:2003
IEC 60947-5-7:2003 |
| Approvals and certificates |
|---|
| UL approval | cULus Listed, Class 2 Power Source |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature | current output -25 … 60 °C (-13 … 140 °F)
voltage output -25 … 70 °C (-13 … 158 °F)
When fixing with one M18 nut, the temperature range for each begins with 0 °C (32 °F). |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) |
| Mechanical specifications |
|---|
| Connection type | Connector plug M8 x 1 , 4-pin |
| Degree of protection | IP67 |
| Material | |
| Housing | Polycarbonate |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Installation position | any position |
| Mass | 13 g |
| Tightening torque, fastening screws | with M3 nuts max. 0.2 Nm
with M18 nuts max. 1 Nm |
| Factory settings |
|---|
| Output | near limit: 70 mm
far limit: 800 mm
Output mode: rising ramp
output type: 4 … 20 mA |
| Beam width | wide |
