Description
Datasheet excerpt: Technical data of OMT120-R103-2EP-IO-V31-L
| Product Description |
|---|
| Distance sensor |
| General specifications |
|---|
| Measurement range | 40 … 120 mm |
| Reference target | standard white, 100 mm x 100 mm |
| Light source | laser diode |
| Light type | modulated visible red light |
| Laser nominal ratings | |
| Note | LASER LIGHT , DO NOT STARE INTO BEAM |
| Laser class | 1 |
| Wave length | 680 nm |
| Beam divergence | > 5 mrad d63 d63 < 1 mm in the range of 50 mm … 250 mm |
| Pulse length | 3 µs |
| Repetition rate | approx. 3 kHz |
| max. pulse energy | 15.2 nJ |
| Angle deviation | max. +/- 1.5 ° |
| Diameter of the light spot | approx. 3 mm at a distance of 120 mm |
| Angle of divergence | approx. 2 ° |
| Ambient light limit | EN 60947-5-2 : 30000 Lux |
| Resolution | 0.1 mm |
| Functional safety related parameters |
|---|
| MTTFd | 560 a |
| Mission Time (TM) | 20 a |
| Diagnostic Coverage (DC) | 0 % |
| Indicators/operating means |
|---|
| Operation indicator | LED green:
constantly on – power on
flashing (4Hz) – short circuit
flashing with short break (1 Hz) – IO-Link mode |
| Function indicator | LED yellow:
constantly on – switch output active
constantly off – switch output inactive |
| Control elements | Teach-In key |
| Control elements | 5-step rotary switch for operating modes selection |
| Electrical specifications |
|---|
| Operating voltage | 10 … 30 V DC |
| Ripple | max. 10 % |
| No-load supply current | < 25 mA at 24 V supply voltage |
| Protection class | III |
| Interface |
|---|
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| Device profile | Smart Sensor |
| Transfer rate | COM 2 (38.4 kBaud) |
| IO-Link Revision | 1.1 |
| Min. cycle time | 3 ms |
| Process data width | Process data input 3 Byte
Process data output 2 Bit |
| SIO mode support | yes |
| Device ID | 0x11090A (1116426) |
| Compatible master port type | A |
| Output |
|---|
| Switching type | The default setting is:
C/Q – Pin4: NPN normally open, PNP normally closed, IO-Link
Q2 – Pin2: NPN normally open, PNP normally closed |
| Signal output | 2 push-pull (4 in 1)outputs, short-circuit protected, reverse polarity protected, overvoltage protected |
| Switching voltage | max. 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Usage category | DC-12 and DC-13 |
| Voltage drop | ≤ 1.5 V DC |
| Response time | 2 ms |
| Conformity |
|---|
| Communication interface | IEC 61131-9 |
| Product standard | EN 60947-5-2 |
| Laser safety | EN 60825-1:2014 |
| Measurement accuracy |
|---|
| Temperature drift | 0.05 %/K |
| Warm up time | 5 min |
| Repeat accuracy | ≤ 1 % |
| Linearity error | ± 1 % |
| Approvals and certificates |
|---|
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| FDA approval | IEC 60825-1:2007 Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 |
| Ambient conditions |
|---|
| Ambient temperature | 10 … 60 °C (50 … 140 °F) |
| Storage temperature | -40 … 70 °C (-40 … 158 °F) |
| Mechanical specifications |
|---|
| Housing width | 15 mm |
| Housing height | 43.9 mm |
| Housing depth | 26.7 mm |
| Degree of protection | IP67 / IP69 / IP69K |
| Connection | M8 x 1 connector, 4-pin |
| Material | |
| Housing | PC (Polycarbonate) |
| Optical face | PMMA |
| Mass | approx. 12 g |
Classifications
| System | Classcode |
|---|
| ECLASS 11.0 | 27270903 |
| ECLASS 10.0.1 | 27270903 |
| ECLASS 9.0 | 27270903 |
| ECLASS 8.0 | 27270903 |
| ECLASS 5.1 | 27270903 |
| ETIM 8.0 | EC001821 |
| ETIM 7.0 | EC001821 |
| ETIM 6.0 | EC001821 |
| ETIM 5.0 | EC001821 |
| UNSPSC 12.1 | 39121528 |
