| General specifications |
|---|
| Signal type | Digital Output |
| Functional safety related parameters |
|---|
| Safety Integrity Level (SIL) | SIL 3 |
| Supply |
|---|
| Connection | SL1: 1a(-), 1b(-); 2a(+), 2b(+) |
| Rated voltage | 20.4 … 30 V DC loop powered
20.4 … 30 V DC bus powered via Termination Board |
| Input current | 62 mA at 24 V, 300 Ω load (per channel) |
| Power dissipation | 1 W at 24 V, 300 Ω load (per channel) |
| Input |
|---|
| Connection side | control side |
| Connection | SL1: 8a(+), 7a(-); 10a(+), 9a(-) bus powered
SL1: 8b(+), 7b(-); 9b(+), 10b(-) loop powered |
| Control input | external switch (dry contact or open collector) non isolated or logic signal input fully floating |
| Signal level | 1-signal: 15…30 V DC (current limited at 3 mA) or contact close (internal 10 kΩ pull-up)
0-signal: 0…5 V DC or contact open |
| Power dissipation | 1 W at 24 V, 300 Ω load (per channel) for loop powered |
| Inrush current | 0.2 A , 15 ms loop powered |
| Output |
|---|
| Connection side | field side |
| Connection | SL2: 5a(+), 5b(-), 7a(+); 1a(+), 1b(-), 3b(+) |
| Internal resistor | approx. 240 Ω |
| Current | ≤ 40 mA |
| Voltage | ≥ 12 V |
| Current limit | 55 mA |
| Open loop voltage | approx. 22.5 V |
| Load | nominal 0.1 … 5 kΩ |
| Switching frequency | – bus powered: filter OFF: max. 150 Hz, filter ON: max. 15 Hz
– loop powered: max. 10 Hz |
| Energized/De-energized delay | – bus powered: filter OFF: 1 ms, filter ON: 10 ms
– loop powered: switch-on 50 ms, switch-off 6 ms (300 Ω load) |
| Fault indication output |
|---|
| Connection | SL1: 6b |
| Output type | open collector transistor (internal fault bus) |
| Fault current | 4 mA pulsing (20 ms ON, 200 ms OFF) |
| Fault level | lead short-circuit detection at < 25 Ω
lead breakage detection at > 100 kΩ typical |
| Galvanic isolation |
|---|
| Output/Output | safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 60 V |
| Output/power supply, inputs, and collective error | safe electrical isolation acc. to EN 60079-11: 2007, voltage peak value 375 V |
| Indicators/settings |
|---|
| Display elements | LEDs |
| Control elements | DIP-switch |
| Configuration | via DIP switches |
| Labeling | space for labeling at the front |
| Directive conformity |
|---|
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Conformity |
|---|
| Electromagnetic compatibility | NE 21:2006
For further information see system description. |
| Degree of protection | IEC 60529:2001 |
| Ambient conditions |
|---|
| Ambient temperature | -20 … 60 °C (-4 … 140 °F) |
| Relative humidity | 5 … 90 %, non-condensing up to 35 °C (95 °F) |
| Mechanical specifications |
|---|
| Degree of protection | IP20 |
| Mass | approx. 140 g |
| Dimensions | 18 x 106 x 128 mm (0.7 x 4.2 x 5 inch) |
| Mounting | on Termination Board |
| Coding | pin 1 and 4 trimmed
For further information see system description. |
| Data for application in connection with hazardous areas |
|---|
| EU-type examination certificate | CESI 10 ATEX 036 |
| Marking |   II (1)G [Ex ia Ga] IIC
II (1)D [Ex ia Da] IIIC
I (M1) [Ex ia Ma] I |
| Output | Ex ia Ga, Ex ia Da, Ex ia Ma |
| Voltage | 26 V |
| Current | 110 mA |
| Power | 715 mW |
| Supply | |
| Maximum safe voltage | 253 V AC (Attention! Um is no rated voltage.) |
| Certificate | PF 10 CERT 1729 X |
| Marking | II 3G Ex nA IIC T4 Gc |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| International approvals |
|---|
| CSA approval | |
| Control drawing | 366-005CS-12B (cCSAus) |
| IECEx approval | |
| IECEx certificate | IECEx CES 10.0013 |
| IECEx marking | [Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I |
| General information |
|---|
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
