| General specifications |
|---|
| Sensing range | 80 … 2000 mm |
| Adjustment range | 120 … 2000 mm |
| Dead band | 0 … 80 mm |
| Standard target plate | 100 mm x 100 mm |
| Transducer frequency | approx. 180 kHz |
| Response delay | 65 ms minimum
195 ms factory setting |
| Indicators/operating means |
|---|
| LED green | solid: Power-on
flashing: Standby mode or program function object detected |
| LED yellow 1 | solid: object in evaluation range
flashing: program function |
| LED yellow 2 | solid: object in detection range
flashing: program function |
| LED red | solid: temperature/program plug not connected
flashing: fault or program function object not detected |
| Temperature/TEACH-IN connector | Temperature compensation , Evaluation range programming , output function setting |
| Electrical specifications |
|---|
| Operating voltage | 10 … 30 V DC , ripple 10 %SS |
| Power consumption | ≤ 900 mW |
| Time delay before availability | ≤ 500 ms |
| Interface |
|---|
| Interface type | RS 232, 9600 Bit/s , no parity, 8 data bits, 1 stop bit |
| Input/Output |
|---|
| Synchronization | bi-directional
0 level -UB…+1 V
1 level: +4 V…+UB
input impedance: > 12 KOhm
synchronization pulse: ≥ 100 µs, synchronization interpulse period: ≥ 2 ms |
| Synchronization frequency | |
| Common mode operation | max. 30 Hz |
| Multiplex operation | ≤ 30 Hz / n , n = number of sensors , n ≤ 5 |
| Output |
|---|
| Output type | 1 current output 4 … 20 mA
1 voltage output 0 … 10 V |
| Resolution | evaluation range [mm]/4000, but ≥ 0.35 mm |
| Deviation of the characteristic curve | ≤ 0.2 % of full-scale value |
| Repeat accuracy | ≤ 0.1 % of full-scale value |
| Load impedance | current output: ≤ 500 Ohm
voltage output: ≥ 1000 Ohm |
| Temperature influence | ≤ 2 % from full-scale value (with temperature compensation)
≤ 0.2 %/K (without temperature compensation) |
Compliance with standards and directives |
|---|
| Standard conformity | |
| Standards | EN IEC 60947-5-2:2020
IEC 60947-5-2:2019
EN 60947-5-7:2003
IEC 60947-5-7:2003 |
| Approvals and certificates UC2000-30GM-IUR2-V15 |
|---|
| UL approval | cULus Listed, General Purpose |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Ambient conditions |
|---|
| Ambient temperature | -25 … 70 °C (-13 … 158 °F) |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) |
| Mechanical specifications |
|---|
| Connection type | Connector plug M12 x 1 , 5-pin |
| Housing diameter | 30 mm |
| Degree of protection | IP65 |
| Material | |
| Housing | stainless steel (1.4305 / AISI 303)
PBT plastic parts |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam |
| Mass | 170 g |
| Factory settings |
|---|
| Output | evaluation limit A1: 200 mm
evaluation limit A2: 2000 mm
rising ramp |
