| General specifications |
|---|
| Signal type | Universal |
| Functional safety related parameters |
|---|
| Safety Integrity Level (SIL) | SIL 2 |
| Supply |
|---|
| Connection | SL1: 1a(-), 1b(-); 2a(+), 2b(+) |
| Rated voltage | 19 … 30 V DC via Termination Board |
| Ripple | ≤ 10 % |
| Rated current | ≤ 30 mA |
| Power consumption | ≤ 700 mW |
| Analog input |
|---|
| Suitable field devices | 2-wire SMART transmitters, current sources |
| Signal | 0/4 … 20 mA , limited to approx. 40 mA (depends on control system) , reverse polarity protected |
| Field circuit | SL2: 5a(+), 5b(-) (2-wire SMART transmitter)
SL2: 5a(+), 1b(-) (2-wire SMART transmitter with current source) |
| Voltage drop | approx. 4 V (current source) |
| Control circuit | SL1: 8a(+), 7a(-) |
| Supply voltage | min. 16 V at 20 mA (2-wire SMART transmitter) |
| Voltage | 15 … 30 V |
| Signal | 0/4 … 20 mA , sink mode , working voltage 15 … 30 V |
| Ripple | 20 mV rms |
| Analog output |
|---|
| Suitable field devices | I/P converters (positioner), on-site-displays |
| Signal | 0/4 … 20 mA |
| Field circuit | SL2: 5a(+), 5b(-) |
| Load | 0 … 650 Ω |
| Voltage | ≥ 13 V at 20 mA |
| Ripple | 20 mV rms |
| Control circuit | SL1: 8a(+), 7a(-) |
| Voltage | 12 … 30 V |
| Signal | 0/4 … 20 mA |
| Line fault detection | > 100 kΩ at max. 30 V, with field wiring open |
| Digital input |
|---|
| Field circuit | SL2: 5a(+), 1a(-) (NAMUR sensor)
SL2: 5a(+), 5b(-) (dry contact) |
| Suitable field devices | NAMUR sensors according to IEC/EN 60947-5-6, dry contacts |
| Signal | 0.1 … 9 mA , sink mode |
| Open loop voltage | approx. 10 V DC , 1 kΩ series resistance |
| Signal | 0.1 … 9 mA |
| Control circuit | SL1: 8a(+), 7a(-) |
| Voltage | 13 … 30 V |
| Digital output |
|---|
| Field circuit | SL2: 5a(+), 5b(-) |
| Suitable field devices | solenoid valves, acoustic or visual alarms |
| Drive capability | 12 V / 40 mA at 300 Ω load |
| Open loop voltage | approx. 22 V |
| Current limit | 45 mA |
| Internal resistor | min. 240 Ω |
| Control circuit | SL1: 8a(+), 7a(-) |
| Voltage | 1-signal: 19 … 30 V DC
0-signal: 0 … 5 V DC |
| Current | 1-signal: 0 … 45 mA, depending on the output load
0-signal: < 0.1 mA, independent of the output load |
| Power dissipation | 1.1 W at 24 V, 300 Ω load (digital output) |
| Transfer characteristics |
|---|
| Deviation | at 20 °C (68 °F)
≤ ±20 µA incl. linearity, hysteresis and supply fluctuations at 4 … 20 mA (analog input, analog output)
≤ ±60 µA incl. linearity, hysteresis and supply fluctuations at 0 … 45 mA (digital output) |
| Influence of ambient temperature | < 2 µA/K (0 … 70 °C (32 … 158 °F))
< 3 µA/K (-40 … 0 °C (-40 … 32 °F)) |
| Switching frequency | ≤ 500 Hz with 50 % duty cycle (digital input, NAMUR sensor)
≤ 5 Hz (digital input, dry contact)
≤ 20 Hz (digital output) |
| Frequency range | HART: bandwidth by 0.5 Vpp signal and/or 1 mApp signal 950 … 2500 Hz (analog input, analog output) |
| Settling time | ≤ 20 ms (analog input, analog output)
≤ 1 ms (digital input, NAMUR sensor) |
| Reaction time | ≤ 5 ms , turn-on/turn-off time (digital output) |
| Galvanic isolation |
|---|
| Control/power supply | basic insulation according to IEC/EN 61010-1, rated insulation voltage 60 Veff |
| Directive conformity |
|---|
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Conformity |
|---|
| Electromagnetic compatibility | NE 21:2006
For further information see system description. |
| Degree of protection | IEC 60529:2001 |
| Protection against electrical shock | IEC 61010-1:2010 |
| Input | EN 60947-5-6:2000 |
| Ambient conditions |
|---|
| Ambient temperature | -40 … 70 °C (-40 … 158 °F)
Observe the temperature range limited by derating, see section derating. |
| Storage temperature | -40 … 85 °C (-40 … 185 °F) |
| Relative humidity | 95 % non-condensing |
| Mechanical specifications |
|---|
| Degree of protection | IP20 |
| Mass | approx. 100 g |
| Dimensions | 12.5 x 128 x 106 mm (0.5 x 5.1 x 4.2 inch) |
| Mounting | on Termination Board |
| Coding | pin 1 and 4 trimmed
For further information see system description. |
| Data for application in connection with hazardous areas |
|---|
| EU-type examination certificate | TÜV 14 ATEX 153522 X |
| Marking |   II (1)G [Ex ia Ga] IIC
II (1)D [Ex ia Da] IIIC
I (M1) [Ex ia Ma] I |
| Supply | |
| Maximum safe voltage | 250 V (Attention! The rated voltage can be lower.) |
| Equipment | SL2: 5a(+), 5b(-) |
| Voltage Uo | 25.2 V |
| Current Io | 110 mA |
| Power Po | 693 mW |
| Internal capacitance Ci | 5.7 nF |
| Internal inductance Li | 0 mH |
| Equipment | SL2: 5a(+), 1b(-) |
| Voltage Ui | < 28 V |
| Current Ii | < 115 mA |
| Voltage Uo | 7.2 V |
| Current Io | 0 mA |
| Power Po | 0 mW |
| Internal capacitance Ci | 5.7 nF |
| Internal inductance Li | 0 mH |
| Equipment | SL2: 5a(+), 1a(-) |
| Voltage Uo | 12.6 V |
| Current Io | 13 mA |
| Power Po | 41 mW |
| Internal capacitance Ci | 5.7 nF |
| Internal inductance Li | 0 mH |
| Certificate | TÜV 14 ATEX 153523 X |
| Marking | II 3G Ex ec IIC T4 Gc |
| Galvanic isolation | |
| Input/Other circuits | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-7:2015 |
| International approvals |
|---|
| UL approval | E106378 |
| Control drawing | 116-0408 (cULus) |
| IECEx approval | |
| IECEx certificate | IECEx TUN 15.0004X |
| IECEx marking | [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I
Ex ec IIC T4 Gc |
| General information |
|---|
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
