| General specifications |
|---|
| Signal type | Digital Input |
| Functional safety related parameters |
|---|
| Safety Integrity Level (SIL) | SIL 2 |
| Supply |
|---|
| Connection | terminals 23, 24 |
| Rated voltage | 115 V AC +/- 10 % |
| Rated current | 30 mA |
| Power dissipation/power consumption | ≤ 2 VA / 2 VA |
| Input |
|---|
| Connection side | field side |
| Connection | Input I: intrinsically safe: terminals 1+, 3-
Input II: non-intrinsically safe: terminals 13+, 14- |
| Input I | acc. to EN 60947-5-6 (NAMUR), see manual for electrical data |
| Pulse duration | > 50 µs |
| Input frequency | 0.001 … 5000 Hz |
| Line fault detection | breakage I ≤ 0.15 mA; short-circuit I > 6.5 mA |
| Input II | startup override: 1 … 1000 s, adjustable in steps of 1 s |
| Active/Passive | I > 4 mA (for min. 100 ms)/ I < 1 mA |
| Open circuit voltage/short-circuit current | 18 V / 5 mA |
| Output |
|---|
| Connection side | control side |
| Connection | output I: terminals 10, 11, 12
output II: terminals 16, 17, 18 |
| Output I, II | signal, relay |
| Contact loading | 253 V AC / 2 A / cos φ ≥ 0.7 ; 40 V DC / 2 A |
| Mechanical life | 5 x 107 switching cycles |
| Energized/De-energized delay | approx. 20 ms / approx. 20 ms |
| Transfer characteristics |
|---|
| Input I | |
| Measurement range | 0.001 … 5000 Hz |
| Resolution | 0.1 % of the measurement value , ≥ 0.001 Hz |
| Accuracy | 0.1 % of the measurement value , > 0.001 Hz |
| Measuring time | < 100 ms |
| Influence of ambient temperature | 0.003 %/K (30 ppm) |
| Output I, II | |
| Response delay | ≤ 200 ms |
| Galvanic isolation |
|---|
| Input I/other circuits | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output I, II against eachother | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Output I, II/other circuits | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Start-up override/power supply | reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 Veff |
| Indicators/settings |
|---|
| Display elements | LEDs , display |
| Control elements | Control panel |
| Configuration | via operating buttons |
| Labeling | space for labeling at the front |
| Directive conformity |
|---|
| Electromagnetic compatibility | |
| Directive 2014/30/EU | EN 61326-1:2013 (industrial locations) |
| Low voltage | |
| Directive 2014/35/EU | EN 61010-1:2010 |
| Conformity |
|---|
| Electromagnetic compatibility | NE 21:2006 |
| Degree of protection | IEC 60529:2001 |
| Ambient conditions |
|---|
| Ambient temperature | -20 … 60 °C (-4 … 140 °F)
extended ambient temperature range up to 70 °C (158 °F), refer to manual for necessary mounting conditions |
| Mechanical specifications |
|---|
| Degree of protection | IP20 |
| Connection | screw terminals |
| Mass | 300 g |
| Dimensions | 40 x 119 x 115 mm (1.6 x 4.7 x 4.5 inch) , housing type C2 |
| Mounting | on 35 mm DIN mounting rail acc. to EN 60715:2001 |
| Data for application in connection with hazardous areas |
|---|
| EU-type examination certificate | TÜV 99 ATEX 1408 |
| Marking |   II (1)G [Ex ia Ga] IIC
II (1)D [Ex ia Da] IIIC
I (M1) [Ex ia Ma] I |
| Supply | |
| Maximum safe voltage | 253 V AC (Attention! Um is no rated voltage.) |
| Input I | terminals 1+, 3-: Ex ia |
| Voltage Uo | 10.1 V |
| Current Io | 13.5 mA |
| Power Po | 34 mW (linear characteristic) |
| Input II | terminals 13+, 14- non-intrinsically safe |
| Maximum safe voltage Um | 40 V (Attention! The rated voltage can be lower.) |
| Output I, II | terminals 10, 11, 12; 16, 17, 18 non-intrinsically safe |
| Maximum safe voltage | 253 V (Attention! The rated voltage can be lower.) |
| Contact loading | 253 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load |
| Certificate | TÜV 02 ATEX 1885 X |
| Marking | II 3G Ex nA nC IIC T4 Gc |
| Output I, II | |
| Contact loading | 50 V AC/2 A/cos φ > 0.7; 40 V DC/2 A resistive load |
| Galvanic isolation | |
| Input I/other circuits | safe electrical isolation acc. to IEC/EN 60079-11, voltage peak value 375 V |
| Directive conformity | |
| Directive 2014/34/EU | EN 60079-0:2012+A11:2013 , EN 60079-11:2012 , EN 60079-15:2010 |
| International approvals |
|---|
| FM approval | |
| Control drawing | 16-538FM-12 |
| UL approval | E223772 |
| IECEx approval | |
| IECEx certificate | IECEx TUN 03.0000 |
| IECEx marking | [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I |
| General information |
|---|
| Supplementary information | Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com. |
